How much solar and battery to run a Starlink dish in a campervan?
A Starlink dish runs continuously and pulls more than a laptop. In a campervan in Australia it uses about 1000 Wh a day. Wattonomy sizes the battery (5.12 kWh), the solar (600 W) and every cable around it to AS/NZS 3008, then hands you the wiring diagram and a shoppable parts list.
Built to AS/NZS 3008 standards · free · no account
A real Wattonomy output — a AU campervan running a Starlink dish
System
12 V
Battery
5.12 kWh
Solar
600 W
Inverter
MP 12/1600
SmartSolar 100/501×
200W solar panel3×
Battery → inverter cable4×
Battery → inverter fuse1×
Wire & fuse sizes follow AS/NZS 3008 — each conductor carries its fuse and stays under a 3% voltage drop.
Built to AS/NZS 3008 standards
Gauge · fuse · volt-drop sized
Every spec sourced
Always-on internet is an always-on load.
Starlink runs continuously, so it is often the biggest single draw in a small build. An undersized bank drops it offline overnight, just when you want it. Wattonomy sizes the bank, solar and every cable around it, to AS/NZS 3008.
What it takes to run a Starlink dish
Real numbers from a sized campervan build for Australia, not rules of thumb.
Daily energy
About 1000 Wh a day for the Starlink dish itself, the figure everything else is sized from.
Battery
About 5.12 kWh of LiFePO4 (roughly 427 Ah at 12V) to carry it through the night and a cloudy day.
Solar to replace it
About 600 W of panel replaces a day’s use in fair sun; poor light or winter wants more, or a second charging source.
Cables and fuses
Every conductor sized to carry its fuse, with the voltage drop checked, to AS/NZS 3008.
What you walk away with — free
A full system sized to run your Starlink dish — battery, solar and inverter
A real wiring diagram with cable gauges and fuses
Cable and fuse sizing with the voltage drop checked, to AS/NZS 3008
A shoppable parts list, every line traceable to a standard or datasheet
Building it for real? Unlock the build binder.
Free gets you a safe, correctly-sized design. The build binder gets you the documents to build it right — and prove it's right.
Printable wiring diagram, yours to keep & tape inside the build
Full parts list, every line sourced
The volt-drop & fusing calculation trail — the "why" behind every spec
The build binder is a one-time unlock — no subscription, no auto-renew.
Questions
How many watts does a Starlink dish use?
A Starlink dish draws about 50 W when running, and because it runs much of the day it uses around 1000 Wh. Wattonomy sizes from your real figure, not a rule of thumb.
What size battery runs a Starlink dish in a campervan?
For this build Wattonomy sizes about 5.12 kWh (roughly 427 Ah at 12V) of LiFePO4 — enough to carry the Starlink dish plus your basics through the night and a cloudy day. Your exact number depends on how many days of backup you want.
How much solar do I need to run a Starlink dish?
About 600 W of panel replaces a day’s use in fair sun; poor light, winter or shade wants more, or a second charging source such as a DC-DC charger off the engine. The tool sizes it from your climate.
Is this sized to Australian standards?
Yes. Every cable, fuse and busbar is sized to AS/NZS 3008 using mm², at the 12/24V DC and 230V AC typical of Australia systems. Nothing here is a rule of thumb.
The standards we build to
Plain version: these are the recognized rulebooks your design is sized against, so the numbers hold up to a surveyor, an inspector or an insurer.
AS/NZS 3008The Australian cable-selection standard — current rating and voltage drop.
AS/NZS 3001.2The Australian standard for RV/caravan electrical, including lithium placement.
Wattonomy applies these standards in its calculations. It is not certified, sponsored or endorsed by ABYC, ISO, NFPA or Victron — it sizes your design to meet what they require, and shows the working.
Sized and checked to AS/NZS 3008. Last reviewed June 2026 — see the full methodology for the exact rules behind every number and how each design is validated.
Built by anABYC Certified Master Technician